AS568-165 FFKM O-Ring — 164.77 × 2.62 mm
A balanced industrial section for static face, radial and slow rotary seals across a wide diameter range. With an inside diameter of 164.77 mm and a 2.62 mm cross section, this is a large-bore seal for large-bore machinery and process equipment. Moulded from Aperflu 2275 perfluoroelastomer (FFKM) for continuous service up to 200 °C, this seal resists hot acids, caustics, solvents, fuels and steam.
Dimensions
| Dash number | AS568-165 |
|---|---|
| Inside diameter (ID) | 164.77 mm (6.487 in) |
| Cross section (CS) | 2.62 mm (0.103 in) |
| Outside diameter (OD) | 170.01 mm (6.693 in) |
| Material | Aperflu 2275 perfluoroelastomer (FFKM) |
| Service temperature | up to 200 °C continuous |
Oil & gas and refining
Sour gas, amines, hydrocarbons and high-pressure steam are classic FFKM territory. This seal retains integrity in downhole tools, wellhead assemblies and sub-sea connectors, delivering predictable, long service life in the harshest production environments.
Why Aperflu 2275 FFKM
Perfluoroelastomer (FFKM) is the most chemically and thermally resistant elastomer class available — rated for continuous use beyond 200 °C and stable against well over 1,600 chemicals, which is why it is specified where FKM, silicone and EPDM fail.
Typical applications
General machinery, pumps, compressors, gearboxes and process connections, where Aperflu 2275 outperforms FKM and EPDM in aggressive media and elevated temperature.
Compound properties
| Property | Typical value | Test method |
|---|---|---|
| Hardness | 70 – 71 Shore A | GB/T 39693.4 |
| Tensile strength | 21.2 – 21.8 MPa | GB/T 528 (dumbbell type 2) |
| Elongation at break | 155 – 170 % | GB/T 528 (dumbbell type 2) |
| Compression set, 200 °C × 70 h (25 %, method B) | 15 – 16 % | GB/T 7759.1 |
All values are typical. Every batch is shipped with an individual certificate of analysis and may differ from the typical values listed here.
Chemical resistance
The fully fluorinated backbone of Aperflu 2275 resists the aggressive media that attack FKM, EPDM and silicone — including concentrated hydrochloric, nitric, sulfuric and glacial acetic acids, strong caustics, and a broad range of solvents and fuels. Refer to the rating table below for guidance, and confirm your exact media with our engineers.
| Media group | Rating |
|---|---|
| Hydrochloric acid | Excellent |
| Nitric acid | Excellent |
| Sulfuric acid | Excellent |
| Acetic acid (glacial) | Excellent |
| Other hot organic & inorganic acids | Excellent |
| Caustics (ammonia, NaOH up to 50 %) | Excellent |
| Ketones, aldehydes, esters, ethers, alcohols | Excellent |
| Solvents, fuels, hydrocarbons, sour gases | Excellent |
| Steam and hot water | Excellent |
| Ethylene diamine & high-temp amines | Good – contact us for grade selection |
| Clean-in-place (CIP) / steam-in-place (SIP) agents | Excellent |
| Active pharmaceutical ingredients (APIs) | Excellent |
Ratings are typical for peroxide-cured FFKM compounds at room and elevated temperature. Final suitability depends on concentration, temperature and pressure — contact us for a compound recommendation against your specific media.
Need AS568-165 in a custom colour or quantity?
Tell us your dash number, quantity and service media. We quote within 24 hours.
Request a Quote