AS568-111 FFKM O-Ring — 10.77 × 2.62 mm
A balanced industrial section for static face, radial and slow rotary seals across a wide diameter range. With an inside diameter of 10.77 mm and a 2.62 mm cross section, this is a small-bore seal for compact assemblies and small-bore equipment. Moulded from Aperflu 2275 perfluoroelastomer (FFKM) for continuous service up to 200 °C, this seal resists hot acids, caustics, solvents, fuels and steam.
Dimensions
| Dash number | AS568-111 |
|---|---|
| Inside diameter (ID) | 10.77 mm (0.424 in) |
| Cross section (CS) | 2.62 mm (0.103 in) |
| Outside diameter (OD) | 16.01 mm (0.63 in) |
| Material | Aperflu 2275 perfluoroelastomer (FFKM) |
| Service temperature | up to 200 °C continuous |
Chemical synthesis and reactors
Reactor flanges, distillation columns, agitators and transfer lines carrying corrosive intermediates. The perfluoroelastomer resists swelling and degradation, keeping batch consistency and seal integrity across long runs.
Why Aperflu 2275 FFKM
Compared with bisphenol-cured FKM, peroxide-cured FFKM keeps its sealing force longer at temperature — critical for static and slow-dynamic duty in chemical service.
Typical applications
General machinery, pumps, compressors, gearboxes and process connections, where Aperflu 2275 outperforms FKM and EPDM in aggressive media and elevated temperature.
Compound properties
| Property | Typical value | Test method |
|---|---|---|
| Hardness | 70 – 71 Shore A | GB/T 39693.4 |
| Tensile strength | 21.2 – 21.8 MPa | GB/T 528 (dumbbell type 2) |
| Elongation at break | 155 – 170 % | GB/T 528 (dumbbell type 2) |
| Compression set, 200 °C × 70 h (25 %, method B) | 15 – 16 % | GB/T 7759.1 |
All values are typical. Every batch is shipped with an individual certificate of analysis and may differ from the typical values listed here.
Chemical resistance
The fully fluorinated backbone of Aperflu 2275 resists the aggressive media that attack FKM, EPDM and silicone — including concentrated hydrochloric, nitric, sulfuric and glacial acetic acids, strong caustics, and a broad range of solvents and fuels. Refer to the rating table below for guidance, and confirm your exact media with our engineers.
| Media group | Rating |
|---|---|
| Hydrochloric acid | Excellent |
| Nitric acid | Excellent |
| Sulfuric acid | Excellent |
| Acetic acid (glacial) | Excellent |
| Other hot organic & inorganic acids | Excellent |
| Caustics (ammonia, NaOH up to 50 %) | Excellent |
| Ketones, aldehydes, esters, ethers, alcohols | Excellent |
| Solvents, fuels, hydrocarbons, sour gases | Excellent |
| Steam and hot water | Excellent |
| Ethylene diamine & high-temp amines | Good – contact us for grade selection |
| Clean-in-place (CIP) / steam-in-place (SIP) agents | Excellent |
| Active pharmaceutical ingredients (APIs) | Excellent |
Ratings are typical for peroxide-cured FFKM compounds at room and elevated temperature. Final suitability depends on concentration, temperature and pressure — contact us for a compound recommendation against your specific media.
More AS568 2.62 mm cross-section sizes
Need AS568-111 in a custom colour or quantity?
Tell us your dash number, quantity and service media. We quote within 24 hours.
Request a Quote